Three Ways to Check Soundness of Poly Tanks

Agricultural producers use polyethylene – poly for short – for many purposes on the farm, such as chemical storage and chemical application. Poly tanks have a tremendous benefit over other types of tanks. They can be cheaper, available in various sizes, corrosive-resistant, and compatible with many different liquids. There is, however, one drawback: they will fail (Figure 1). The key to good poly tank management is to know the condition of the tank before it cracks or ruptures.

Figure 1. Collapsed poly tank. (Photo: Jack Knorek, Michigan Department of Agriculture and Rural Development)

Figure 1. Collapsed poly tank. (Photo: Jack Knorek, Michigan Department of Agriculture and Rural Development)

Indicators of Poly Tank Condition

There are three indicators of tank integrity: scratches, crazing, and cracks.

(1) Scratches are on the surface; they can be seen and felt.

(2) Crazing is a network of fine lines or cracks, which may look like a patchwork. They cannot be noticed with a visual inspection. Crazing is within the tank wall and can be a sign of deterioration of the plastic, which may lead to cracks. Tanks that show signs of crazing will still hold liquids, but the integrity of the tank is questionable, so caution should be used when putting any hazardous substance into the container.

(3) Cracks can be seen and felt; they extend through the plastic wall. Cracks may run parallel or at right angles.

Testing Poly Tanks

Testing poly tanks is a simple procedure. There are three different methods that can be used after the tank has been in use: candling, using a water soluble marker, and the ever popular bat method. After purchasing a new tank, fill it with water and let it set overnight before putting any hazardous substance into it; this will ensure that there are no leaks. For all of the following methods, first do a visual inspection by looking for any scratches or surface damage.

(1) Candling is using light to visually inspect a tank. A bright cool light is needed for this procedure. The first step is to inspect the outside of the tank. Place a light, flood light or a very bright flashlight inside the tank while you look on the outside for any cracks or crazes. The next step is to inspect the inside of the tank. Place the light on the outside of the tank and have someone look through the fill opening. Do not allow anyone to put their head inside the tank. You may want to consider using a camera to record the inspection from the top of the tank.

(2) Marking the tank with a water soluble marker is a good, safe way to determine if the tank has integrity problems. This method will show if the tank has crazing issues as well as cracks. Start by checking the areas that get the most UV, or sunlight, exposure. Rub a water soluble marker in a 6-inch by 6-inch section and then quickly wipe it off with a paper towel or dry cloth. If there is any crazing or cracking, the ink will have penetrated the tank surface. Repeat this procedure in several locations on the tank to check for crazing.

If the test reveals cracking or spider webbing with the lines going in all directions, this is a sign of deterioration. Test this tank often and if possible only use it for water. If the test reveals a checkered appearance, this could mean “dry rot” and the tank will lose its ability to expand and will become brittle. These tanks should be replaced or only used for water. If the tank has parallel lines, this is the early stages of UV damage and the tank should be monitored. If the lines are around the fittings, the tank should be replaced immediately or only used for water.

(3) The bat method involves testing the empty tank’s brittleness by hitting it with a baseball bat. This method is the simplest and is a great method to check tanks that have cracking on them. A good poly tank is flexible and needs to bend in and out as it is filled and emptied. Tanks that are brittle lose their ability to expand under pressure and to move when impacted.

For additional information, see Purdue Extension publication,  Poly Tanks for Farms and Businesses (PPP-77)

 

The above information was taken from the article Poly Tank Inspection Techniques by Christina Curell, Michigan State University Extension (posted April 18, 2013)

Submitted by Lee Townsend, Extension Entomologist

 

 

Posted in Pesticide Topics